Concrete Paint Removal

Strip Coatings from Concrete — Fast, Clean, Plus Contained

The Marineshaver™ Pro strips paint, epoxy, plus coatings from concrete floors, foundations, walls, plus patios at roughly one square foot every 20 to 30 seconds. Built-in dust collection captures debris into a wet/dry or HEPA vacuum. No chemicals. No sandblasting. No pressure washing. No dust clouds.

Made in the USA by the family that invented it, in our Cranston, Rhode Island factory since 1985.

Why the Marineshaver™ Pro for Concrete

Other methods of removing paint from concrete are slow, messy, or both.

Method Speed Mess Limitations
Chemical strippers 4 to 24 hours per application, often multiple rounds Goopy residue, requires disposal Cannot penetrate thick coatings in one pass. Chemicals seep into porous concrete.
Pressure washing Moderate Water runoff, potential lead contamination Inconsistent results. Does not remove coatings bonded to the surface.
Sandblasting / soda blasting Moderate Dust clouds, media everywhere Requires containment. Can damage the concrete surface.
Floor grinder Fast on large flat areas Fine dust Aggressive. Can gouge or damage concrete. Not designed for paint removal.
Marineshaver™ Pro 20 to 30 seconds per sq ft Dust captured into vacuum Flat surfaces only. Diamond Tipped Blades required. Blade life: 200 sq ft on concrete.

What You Need to Know About Concrete

Variable speed matters on concrete. The Marineshaver™ Pro’s variable speed control lets you match RPM to the coating type plus thickness. Start slower on thin coatings to avoid gouging. Open up the speed on thick epoxy or multiple paint layers.

Lead paint on concrete. If the concrete was painted before 1978, test for lead before stripping. Pair your Marineshaver™ Pro with a HEPA vacuum for lead-safe work under EPA guidelines. Read our lead-safe paint removal guide.

Frequently Asked Questions

Can the Marineshaver™ Pro remove paint from concrete?

Yes. The Marineshaver™ Pro strips paint, epoxy, plus coatings from flat concrete surfaces at roughly 20 to 30 seconds per square foot. Diamond Tipped Blades are required for concrete. Built-in dust collection captures debris into a vacuum for clean, contained removal without chemicals or sandblasting.

What blades do I need for concrete?

Diamond Tipped Blades. Tungsten carbide blades are for wood plus fiberglass only. Diamond Tipped Blades strip up to 200 square feet on concrete, so plan for multiple blade sets on larger jobs. Each set fills the three blade pockets in the cutting disc. Blade replacement takes minutes with no special tools.

Is the Marineshaver™ Pro better than a chemical stripper for concrete?

The Marineshaver™ Pro strips coatings from concrete in seconds per square foot. Chemical strippers require four to 24 hours of dwell time per application, often need multiple rounds, plus leave goopy residue that must be disposed of. The Marineshaver captures debris into a vacuum. No chemicals, no residue, no drying time.

Will the Marineshaver™ Pro work on a concrete garage floor?

Yes, on flat concrete floors. The tool strips paint, epoxy, plus other coatings from garage floors, basement floors, plus patios. Pair it with a HEPA vacuum for dust-free work in enclosed spaces. It does not work on textured or stamped concrete.

How long do Diamond Tipped Blades last on concrete?

Diamond Tipped Blades last up to 200 square feet on concrete. Blade life is shorter on concrete than on wood or fiberglass because concrete is a harder surface. For a two-car garage floor (roughly 400 square feet), plan on two sets of blades. Blades are $199 per set.

Can I remove epoxy from a concrete floor with the Marineshaver™ Pro?

Yes. The Marineshaver™ Pro removes epoxy coatings from concrete floors at the same speed as paint — roughly 20 to 30 seconds per square foot. Use Diamond Tipped Blades plus start at a lower speed setting, then increase as needed. Built-in dust collection keeps the workspace clean.