Marineshaver™ Pro – gelcoat stripper and paint remover


Paintshaver-1Scroll to the bottom of the page for pricing and videos.

Note: The Marineshaver and the Paintshaver are the same tool with the exception of the blades. The Paintshaver comes with Tungsten Carbide blades and the Marineshaver comes with Diamond blades. Also available in a 240 Volt Version. See link below.

The MarineShaver™ Pro strips gelcoat and anti-fouling paint from fiberglass boats and paint from wooden boats at a rate of 1 square foot in 20 seconds. You can strip the gelcoat on a 30 foot sailboat in about 8 hours. It will also strip coatings from concrete and steel surfaces. Works on large curved surfaces like boat bottoms.

The ecologically safe MarineShaver™ Pro with dust-collector allows retrieval of the stripped debris into a wet/dry or HEPA vacuum.

The Marineshaver Pro is available with 2 different motor options. The 12 Amp BRUSHLESS Variable Speed motor and the 13 Amp Variable Speed motor with brushes. The 13 Amp has more power, but weighs 1.25 lbs. more than the 12 Amp. The 12 Amp BRUSHLESS is lighter, requires less maintenance and has more advanced electronics.

Priced under $1000, the MarineShaver™ Pro is less than half the cost of other gelcoat planers on the market and also comes with a Lifetime Warranty.

The MarineShaver™ Pro comes standard with our New Diamond Tipped Blades which are designed for harder gelcoat and epoxy coatings.

The Replaceable Diamond Tipped Blades do not generate excessive heat and will last up to 2000 square feet on gelcoat and anti-fouling paint and up to 500 square feet on concrete and steel.

The MarineShaver™ Pro eliminates the need for dangerous chemicals and sandblasting. Abrasive grinding of gelcoat creates heat that could damage fiberglass laminates and substrates.

The depth of cut is fully adjustable from 0 to .100” (2.5mm).

The MarineShaver™ Pro is portable, lightweight, inexpensive to operate and can be used indoors and outdoors.

Other gelcoat strippers use a drum type cutter which will only work on fiberglass sail boats. The MarineShaver™ Pro will strip gelcoat and anti-fouling paint from power boats with strakes, sailboats, wood lapstrake, plywood, steel and aluminum boats.

Specifications:

12 Amp Brushless Motor: 120 Volts, 1300 Watts, Variable Speed 2800-10,000 RPM, 5.5 lbs., 2.6″ cutter width, 0-.100″ depth of cut, Lifetime Warranty, Soft Start Motor with Anti-KickBack Protection.

13 Amp Motor: 120 Volts, 1500 Watts, Variable Speed 2800-10,500 RPM, 6.75 lbs., 2.6″ cutter width, 0-.100″ depth of cut, Lifetime Warranty, Soft Start Motor with Anti-KickBack Protection.

Marineshaver 1B
The Marineshaver™ Pro stripping gelcoat from a fiberglass boat bottom


Need 240 Volts? The Marineshaver Pro is Available in a 240 Volt Version for countries outside North America. Click the link below to order.

*** Click here for 240 Volt Marineshaver® Pro info and to order***


 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 


12 Amp BRUSHLESS Marineshaver Pro

Showing all 2 Results
View Cart Product successfully added to your cart.

13 Amp Marineshaver Pro

Showing all 2 Results
View Cart Product successfully added to your cart.

Marineshaver Pro related products

Showing all 2 Results
View Cart Product successfully added to your cart.

Orbital Sandervac and related products

Showing all 10 Results
View Cart Product successfully added to your cart.